Effect of Heat Treatment and 1,5% Magnesium Addition on Density, Hardness, and Tensile Strength of Al-Cu-Mg Alloys
DOI:
https://doi.org/10.71225/jstn.v1i3.61Keywords:
Aluminium , Heat Treatment, Vickers hardness testt, Tensile test, DensityAbstract
This research focuses on adding aluminum 1100 combinations by adding magnesium (Mg) as much as 1.5% and varying the percentage of copper (Cu). 3.9%, 4.1%, 4.3%/ with heat treatment at temperatures of 1000C, 2000C, 3000C, and 4000C with a holding time at each temperature of 120 minutes, then tested the aluminum combination's density, Vickers hardness, and tensile strength. The final results of this study showed that in the density test, the highest density value obtained was 4.24 gr/cm3 in a mixture of 1.5% magnesium and 4.3% copper (Cu) with a temperature of 2000C. In the Vickers hardness test, the highest hardness value was 83.9 HVN in a mixture of 1.5% magnesium and 4.3% copper with a temperature of 4000C. The final result of the research conducted was to obtain the tensile strength results of each specimen by obtaining the maximum tensile strength of the 4.1% Cu mixture specimen with a temperature of 4000C of 163.2698 Mpa and the highest strain value in the 4.3% Cu mixture specimen with a temperature of 4000C of 0.0472 %, for the results of the lowest elastic modulus value in the 4.3% Cu mixture specimen with a temperature of 2000C of 3147.319 Mpa and the highest value of the 4.1 % Cu mixture specimen with a temperature of 4000C of 5947.898 Mpa.
References
J. Lu, G. Wei, Y. Yu, C. Guo, and L. Jiang, “Aluminum alloy AA2024 anodized from the mixed acid system with enhanced mechanical properties,” Surfaces and Interfaces, vol. 13, no. January, pp. 46–50, 2018, doi: 10.1016/j.surfin.2018.08.003.
A. Wisnujati, H. Wijayanto, and A. M. Widodo, Proceedings of the First Mandalika International Multi-Conference on Science and Engineering 2022, MIMSE 2022 (Mechanical and Electrical), vol. 2. Atlantis Press International BV, 2023. doi: 10.2991/978-94-6463-078-7.
H. Wang et al., “Effect of Mg content on microstructure and properties of Zn-Al-Cu Alloy,” IOP Conf. Ser. Earth Environ. Sci., vol. 675, no. 1, 2021, doi: 10.1088/1755-1315/675/1/012059.
P. Li et al., “Effect of post-weld heat treatment on the inhomogeneity of mechanical properties and corrosion behavior of rotary friction welded 2024 aluminum alloy joint,” J. Manuf. Process., vol. 75, no. January 2022, pp. 1012–1022, 2022, doi: 10.1016/j.jmapro.2022.01.059.
D. Brough and H. Jouhara, “The aluminium industry: A review on state-of-the-art technologies, environmental impacts and possibilities for waste heat recovery,” Int. J. Thermofluids, vol. 1–2, 2020, doi: 10.1016/j.ijft.2019.100007.
R. Wang, Q. Zhu, Y. Zuo, L. Cheng, and J. Wang, “The control of as-cast structure of 2024 aluminum alloy with intensive melt shearing and its effect on microstructure and mechanical properties after T4 treatment,” J. Mater. Res. Technol., vol. 24, pp. 3179–3193, 2023, doi: 10.1016/j.jmrt.2023.03.225.
Z. Sun, Y. Ma, S. Ma, H. Xiong, and B. Chen, “Mechanical properties and corrosion resistance enhancement of 2024 aluminum alloy for drill pipe after heat treatment and Sr modification,” Mater. Today Commun., vol. 36, no. 938, p. 106805, 2023, doi: 10.1016/j.mtcomm.2023.106805.
W. A. Wirawan et al., “Investigation of mechanical and physical properties of continue drive welding on aluminium alloy (AA6061),” AIP Conf. Proc., vol. 2592, no. November 2022, 2023, doi: 10.1063/5.0114916.
W. Zhu, Y. Deng, and X. Guo, “Influence of adjusting the anodizing and aging sequences on the microstructure, fatigue property and corrosion resistance of anodized AA6082 alloys,” Mater. Charact., vol. 189, no. April, p. 111941, 2022, doi: 10.1016/j.matchar.2022.111941.
X. Li and X. Liu, “Influence of CeO2 Nanoparticles on Structure and Properties of Anodic Oxide Film on 2024 Aluminum Alloy,” Int. J. Electrochem. Sci., vol. 17, no. 5, p. 220521, 2022, doi: 10.20964/2022.05.07.
S. Sarker, M. S. Haque, M. S. A. Alvy, and M. M. H. Abir, “The effects of solution heat treatment on the microstructure and hardness of an aluminum-4% copper alloy with added nickel and tin,” J. Alloy. Metall. Syst., vol. 4, no. August, p. 100042, 2023, doi: 10.1016/j.jalmes.2023.100042.
T. SAVAŞKAN, Z. AZAKLI, and A. P. HEKÌMOĞLU, “Effect of heat treatment on mechanical and wear properties of Zn–40Al–2Cu–2Si alloy,” Trans. Nonferrous Met. Soc. China (English Ed., vol. 31, no. 9, pp. 2651–2663, 2021, doi: 10.1016/S1003-6326(21)65682-0.
R. D. Fu, J. F. Zhang, Y. J. Li, J. Kang, H. J. Liu, and F. C. Zhang, “Effect of welding heat input and post-welding natural aging on hardness of stir zone for friction stir-welded 2024-T3 aluminum alloy thin-sheet,” Mater. Sci. Eng. A, vol. 559, no. 2013, pp. 319–324, 2013, doi: 10.1016/j.msea.2012.08.105.
A. You, M. Be, and I. In, “The Effect of Heating Surface Treatment by Oxy-Acetylene,” vol. 030017, no. December 2019, 2023.
L. Hemmouche, C. Fares, and M. A. Belouchrani, “Influence of heat treatments and anodization on fatigue life of 2017A alloy,” Eng. Fail. Anal., vol. 35, pp. 554–561, 2013, doi: 10.1016/j.engfailanal.2013.05.003.
S. Manojkumar, M. Kumar, M. Ananth, G. Mageshwaran, and P. Hariprakash, “The Effect of Mg and Mn Addition on Hardness, Tensile and Wear Properties of LM6 Aluminum Alloy,” Springer Proc. Mater., vol. 5, no. February 2021, pp. 599–606, 2021, doi: 10.1007/978-981-15-8319-3_59.
A. Djili, B. Bezzazi, N. Zioui, and M. Haboussi, “Effect of natural aging on the tensile properties and the toughness of friction stir welds of 2024-T3 aluminum alloy,” J. Adv. Join. Process., vol. 8, no. July 2023, p. 100153, 2023, doi: 10.1016/j.jajp.2023.100153.
S. Sun, Y. Fang, L. Zhang, C. Li, and S. Hu, “Effects of aging treatment and peripheral coarse grain on the exfoliation corrosion behaviour of 2024 aluminium alloy using SR-CT,” J. Mater. Res. Technol., vol. 9, no. 3, pp. 3219–3229, 2020, doi: 10.1016/j.jmrt.2020.01.069.
F. C. García Rueda, J. Torres González, and J. M. Hernández-López, “Differences between the untreated and treated diffusion zone in the Alclad 2024-T3 aluminum alloy and hard anodic films,” Surf. Coatings Technol., vol. 429, no. August 2021, 2022, doi: 10.1016/j.surfcoat.2021.127939.
M. Azis, Akid Abdul and -, Pramuko IP, Ir, “Pengaruh Artificial Aging Variasi Holding Time 60 Menit, 90 Menit dan 120 Menit Terhadap Struktur Mikro dan Kekerasan Pada Aluminium Paduan (Al-Cu),” Skripsi thesis, 2020, [Online]. Available: http://eprints.ums.ac.id/79983/
Aghastya, A., Wahjono, H. B., Wirawan, W. A., Atmaja, D. S., Rachman, N. F., & Adi, W. T. (2023, May). The effect of heating surface treatment by oxy-acetylene gas on the microstructure and hardness of the UIC R42 rail. In AIP Conference Proceedings (Vol. 2592, No. 1). AIP Publishing.
Boedi, H., Wirawan, W. A., Rozaq, F., & Atmaja, D. S. (2020). The effect of quenching media on surface treatment process on the rel UIC R42 (Union internasionale des chemins de fer-42) endurance. International Journal of Advanced Science and Technology, 29, 1329-1336.
Wirawan, W. A., Wahjono, H. B., Rachman, F. R. N. F., & Rhamadhani, A. (2023, July). Macrostructural and mechanical properties of rails cladded by automatic flame treatment. In AIP Conference Proceedings (Vol. 2689, No. 1). AIP Publishing.
